Tu jesteś: -> R&D Tools -> Lauterbach -> PowerIntegrator (PI)

Produkty wg:
producenta
kategorii
zastosowań

PowerIntegrator (PI)

Zdjęcia

  • Lauterbach - PowerIntegrator (PI)

Opis

The PowerIntegrator module replaces much more expensive logic analyzer systems used for microprocessor system integration. High-speed logic analysis is now possible on every workplace integrated in the debugger software.

  • Timing Analyzer with 500 MHz on all Channels
  • State Analyzer up to 200 MHz DDR
  • 204 Input Channels
  • Transient Recording
  • Time Correlation with other Tracetools
  • Clock Qualifier for State Clock
  • Mixed State and Timing Mode
  • 4 Clock Inputs
  • MICTOR and Standard Probes (single ended)
  • MICTOR differential Probes
  • Analog Voltage and Current Probe
  • 3G/DigRF Protocol Support
34CH Compression-on-PCB to Mictor Adapter Converter TEKTRONIX footprint to MICTOR connector for PowerIntegrator
Analog Probe for PowerIntegrator 4 Channels 0..5 V 12 Bit Resolution, 3 Current Sense Channels, Conversion Rate 625K Samples/Sec applicable to PowerIntegrator and PowerTrace II
DigRF probe set probe set (3 pieces) for 3G/DigRF protocol differential RX; differential TX; single ended SysClkEna and single ended ANY (for free use)
ICD PowerIntegrator Logic Analyzer ICD State-Timing Analyzer, 204 Channels, 200(400) MHz State, 500 MHz Timing, Transient Recording, 512 KFrames, 48 Bit Time-Stamp, Trigger Filter, Trigger Delay, etc. Requires PODBUS-Interface Requires a valid software maintenance of the debug system it is connected to
Mictor Probe for PowerIntegrator Mictor Probe for PowerIntegrator, 34 Channels (32 Data, 2 Clock), 0..5 V Input, 4 pF, 50 kOhm
Mictor Probe for PowerIntegrator DIFFCLOCK Mictor Probe for PowerIntegrator, 33 Channels (32 Data, 1 pair of differential clock), 0..5 V Input, 4 pF, 50 kOhm
Mictor Probe for PowerIntegrator DIFFERENTIAL Mictor Probe for PowerIntegrator, 17 Difference Channels (16 Data, 1 Clock), 0..5 V Input, 4 pF, 50 kOhm applicable to PowerIntegrator and PowerTrace II
PowerIntegrator Adapter SODIMM DDR/DDR2 400MHz Adapter SODIMM DDR to MICTOR Requires two Mictor Probes plus one Mictor Differential Clock Probe
PowerIntegrator Adapter SODIMM DDR/DDR2 400MHz Inverse Adapter SODIMM DDR to MICTOR (left-hand version) Requires two Mictor Probes plus one Mictor Differential Clock Probe
PowerIntegrator Adapter SODIMM SDRAM Adapter SODIMM SDRAM to MICTOR Requires three Mictor Probes
PowerIntegrator Adapter SODIMM SDRAM Inverse Adapter SODIMM SDRAM to MICTOR (left-hand version) Requires three Mictor Probes
PowerIntegrator Adapter for DRAM Adapter DRAM to MICTOR
PowerIntegrator Adapter to ESICON Adaptor for ESI-CON. plugged between target and Eprom-Simlator-Probe Requires 2 Mictor Probes or 3 Standard Probes
PowerIntegrator II Logic Analyzer 1/2/4 GByte ICD State-Timing Analyzer, 102 Channels, 200 (400) MHz State, 500 MHz Timing, Transient Recording, 256 MFrames, 48 Bit Time-Stamp, Trigger Filter, Trigger Delay, etc. Requires Power Debug II Ethernet (LA-7699) Requires a valid software maintenance of the debug system it is connected to
Samtec Probe for PowerIntegrator Samtec Probe for PowerIntegrator, 34 Channels (32 Data, 2 Clock), 0..5 V Input, 4 pF, 50 kOhm
Samtec Probe for PowerIntegrator DIFFCLOCK Samtec Probe for PowerIntegrator, 33 Channels (32 Data, 1 pair of differential clock), 0..5 V Input, 4 pF, 50 kOhm
Standard Probe for PowerIntegrator Standard Probe for PowerIntegrator, 17 Channels (16 Data, 1 Clock), 0..5 V Input, 4 pF, 50 KOhm includes a 20 pin male-male adaptor
USB2 Probe for PowerIntegrator For recording of USB1x and USB2 Support for filtering, trigger and display on PID protocol level

Best view with Internet Explorer 7/8 or Mozilla Firefox at 1280x1024 resolution or higher.

Copyright © 2009-2010 QUANTUM Corp. All rights reserved.
Baza Firm